CARBON FIBER FREE FLOAT HANDGUARDS

Technical Specifications
AR15
WEIGHT (no barrel nut)
LENGTH OVERALL
(face of receiver to end of handguard)
Inside Diameter
Outside Diameter
MATERIAL
ACCEPTS RAILS
*Please Note:
7.25"
10"
106g
3.7oz
132g
4.6oz
12"
147g
5.1oz
15"
154g
5.41oz
7.25"
10"
12"
15"
1.932"
1.786"
1.932"
1.786"
1.932"
1.786"
1.932"
1.786"
35-50 Carbon Fiber / 7075 Aluminum
Magpul M-LOK 3, 5 & 7 Slot Polymer Rails
Almost all low profile gas blocks of inside diameters up to .750 will fit with clearance inside our AR15 handguards. .875 gas blocks may require a slight modification to the inside of our handguard. Please contact us directly for details.
LARGE FRAME
WEIGHT (no barrel nut)
*Barrel Nut is 47g / 1.63oz and uses a 1-7/16" crowfoot wrench.
LENGTH OVERALL
(face of receiver to end of handguard)
Inside Diameter
Outside Diameter
12"
166g
5.83oz
15"
196g
6.90oz
12"
15"
2.00"
2.00"
2.126"
2.126"
MATERIAL
ACCEPTS RAILS
*Please Note:
35-50 Carbon Fiber / 7075 Aluminum
Magpul M-LOK 3, 5 & 7 Slot Polymer Rails
Our standard barrel nut has an outside dimension of 1.542” that fit perfectly inside our large frame handguards. However, there can be differences between the width and the thread pitch on the inside of a barrel nut. Our standard thread pitch is 16 TPI which fits your standard DPMS platforms and almost all large frame upper receivers. If your width or thread pitch varies from this, please contact us directly before placing your order.
PCC
10"
12"
14"
15"
WEIGHT (no barrel nut)
*Barrel Nut is 37g / 1.30oz and uses 1.25" crowfoot wrench.
g
oz
116g
4.07oz
124g
4.37oz
130g
4.58oz
LENGTH OVERALL
(face of receiver to end of handguard)
10"
12"
14"
15"
Inside Diameter
Outside Diameter
MATERIAL
ACCEPTS RAILS
*Please Note:
1.535"
1.690"
1.535"
1.690"
1.535"
1.690"
1.535"
1.690"
35-50 Carbon Fiber / 7075 Aluminum
Magpul M-LOK 3, 5 & 7 Slot Polymer Rails
The diameter of the PCC Handguard will not allow room for a gas system - specifically where the gas tube enters the upper receiver.
WEIGHT (no barrel nut)
*Barrel Nut is 37g / 1.30oz and uses 1.25" crowfoot wrench.
Smoke Composites carbon fiber handguards are designed with weight and comfort in mind. The material and shape are optimized to help create some of the lightest, most ergonomic hand guards available.
The properties of the carbon fiber, specifically its low thermal mass combined with its high thermal conductivity, and the pattern in which the material orientation is laid out, creates the most efficient hand guard in terms of heat dissipation. This translates into the shooter being able to comfortably handle the gun after hundreds of rounds have been sent downrange.
*Custom length handguards can be made to customer specifications for an additional charge of $25. For custom orders, please email us directly:
**Barrel Nut is included with each handguard. Additional Barrel Nuts can be ordered if needed.
AR15
7.25" AR15 Handguard
$259
+ tax
10" AR15 Handguard
$289
+ tax
12" AR15 Handguard
+ tax
$299
15" AR15 Handguard
$309
+ tax
LARGE FRAME
12" Large Frame Handguard
$299
+ tax
*fits .308, 6.5 Creedmoor and many more
15" Large Frame Handguard
$309
+ tax
*fits .308, 6.5 Creedmoor and many more
PCC
10" PCC Handguard
$209
+ tax
12" PCC Handguard
$219
+ tax
14" PCC Handguard
$229
+ tax
15" PCC Handguard
$239
+ tax
*If you do not see the size handguard you would like listed, please email us directly:
Carbon Fiber Top Rail
Upgrade
$69
+ tax
***Please Note: Top Rails installed on a PCC Handguard will not line up with the flat top on the upper receiver.
CARBON FIBER SIG MPX HANDGUARD

Technical Specifications
SIG MPX
WEIGHT (no barrel nut)
The MPX handguard slides on similar to the stock handguard and is fixed in place with a set screw on the bottom side. A 5-32 Allen Wrench can be used to tighten the set screw.
Inside Diameter
Outside Diameter
SHORT
152g
5.4oz
LONG
164g
5.8oz
1.520"
1.375"
1.520"
1.375"
MATERIAL
ACCEPTS RAILS
35-50 Carbon Fiber / 7075 Aluminum
Magpul M-LOK 3, 5 & 7 Slot Polymer Rails
Introducing the SIG MPX Handguard
This simple design attaches with one set screw and is completely free floating, with no portion of the handguard or mount touching the barrel.
The SIG MPX Handguard comes in two sizes to fit a 14.5" (Short) barrel or a 16" (Long) barrel.
*Custom length MPX handguards can be made to customer specifications for an additional charge of $25. For custom orders, please email us directly:
SIG MPX
Short - SIG MPX Handguard
$279
+ tax
Long - SIG MPX Handguard
$289
+ tax